The Installation, Calibration and Verification of a POS MV OceanMaster System

As with most new vessel charters, A-2-Sea was starting from scratch when mobilizing the Noortruck with its new Applanix POS MV OceanMaster, so careful consideration was required for sensor location. The placement of GNSS antennas, IMUs and sonar equipment can directly affect system performance.

A precise and thorough dimensional control survey, sensor calibrations and equipment verifications are vital for high-quality hydrographic data production. The Applanix POS MV OceanMaster is perfectly suited to a vessel the size of Noortruck, due to the accuracy the system provides over longer lever arms.

Installing the Inertial Measurement Units (IMU)

In order to ensure redundancy, A-2-Sea identified two IMU locations on the vessel. The primary IMU was installed in a location that was identified as secure, elevated above the deck and close to the centreline and centre of rotation of the vessel. A-2-Sea Design Engineers measured and designed an aluminium plate and box to support, secure and protect the IMU. The Applanix base plate could then be secured on to the aluminium plate before being boxed in.

A secondary IMU location was also identified in the cofferdam space (under the wheelhouse). This was identified as it was secure, protected and close to the centreline and centre of gravity. Positioning this location close to the entrance to the cofferdam allowed for the clear line-of-sight access for the dimensional control survey. Again, an aluminium plate was designed by A-2-Sea engineers as an intermediate plate between the cofferdam deck and the IMU plate. The secondary location allowed for redundancy should there be any issues with the primary location.

The Applanix Mounting Plate is a bespoke design capable of accommodating a variety of IMU types. The principle behind the design means that surveyors can survey in the mounting plate, giving them the flexibility of swapping out IMUs without having to re-survey misalignment angles or offsets. A-2-Sea had the luxury of two locations and two mounting plates, giving it flexibility.

Installing the GNSS antennas

The Applanix POS MV OceanMaster uses GAMS (GNSS Azimuth Measurement Subsystem) to aid the IMU in heading calculations. This unique feature uses two GNSS antennas to determine a GNSS-based heading that is accurate to 0.01deg when blended with the inertial navigation solution.

To optimize antenna location, A2Sea engineers were required to come with a design to ensure a secure and rigid mounting location, free from external interference. Multiple antenna mount points were made available and measured to provide different options and backups.

The Dimensional Control Survey

The installation on the Noortruck took place while the vessel was in dry dock, ensuring a stable platform from which to carry out precise Total Station Dimensional Control Survey.

Surveyors adopted the technique of defining a vessel reference frame, then establishing sensor locations and rotations with respect to that vessel reference frame (VRF). A Common Reference Point (CRP) was defined as the target on the IMU housing, with all sensor offsets measured relative to this location. As well as sensor offsets, the vessel Centre of Rotation (COR) was also defined, which is key for optimal Heave measurements.

All Total Station coordinates were within ±0.5mm for each ordinate. These values were obtained by observations from multiple station setups and the mean obtained, showing on average a standard deviation of 0.5mm.

During the measurement process, permanent and recoverable control points were defined throughout the vessel within the specified tolerance of ±0.01m relative (at the 95% confidence level) in X, Y and Z.

Similarly, all sensors were established within the VRF to within a tolerance of ±0.02m relative (at the 95% confidence level) in X, Y and Z.

The final step was to determine the IMU frame with regard to the vessel frame. By extending the baseline of the IMU plate, the misalignment angles were determined. The IMU mounting plate has precisely machined grooved sides in the X and Y directions allowing a bar to be placed along these edges to increase the baseline length with which the mounting angle is measured. The longer this baseline, the more precisely the angular component can be computed from the 3D coordinate values.

The Verifications

GAMS

During the Dimensional Control Survey, the Primary and Secondary antenna locations were precisely measured and the X, Y, Z baseline vector components determined. To verify these measurements, a dynamic GAMS calibration was completed at sea. By starting with zero values in the GAMS parameter setup, a series of dynamic manoeuvres were completed, allowing the POS MV to calculate the GAMS parameters automatically. The results from the dynamic calibration were within close agreement to those measured in the dimensional control:

The values from the Dimensional Control were used going forwards as these were deemed more precise. The dynamic GAMS calibration is dependent on quality GNSS measurements and sufficient vessel dynamics, which can often be hard to achieve on larger vessels. Hence the GAMS calibration process acts as a validation, checking for gross errors in the dimensional control survey.

Position Checks

Whilst alongside, position checks were carried out using RTK enabled Leica GNSS receivers. The GNSS antennas were placed at previously measured control points and position data was logged. These control points were also defined as nodes in QPS QINSy software, to which the POS MV data was interfaced.

The POS MV was utilizing the real-time Trimble RTX® correction service data delivered over L-Band, to provide centimetre level accuracy.

Trimble RTX provides centimetre level accuracy on a global level. Trimble RTX utilizes real-time satellite measurements from a global network of tracking stations, along with highly accurate atmospheric models and algorithms to generate Trimble RTX corrections. These corrections are then broadcast to the receiver via a set of geostationary satellites or over the internet.

A comparison of RTK GNSS data and POS MV GNSS aided inertial data, translated to nodes within QINSy, showed a close agreement, meeting the project specification.

With the POS MV installed, calibrated and verified, further sensor calibrations specific to the project were carried out.

Ongoing work

The Noortruck is currently engaged in nautical charting work for the Civil Hydrography Programme off the east coast of the UK. As part of a collaboration between Applanix, Trimble and A-2-Sea, Trimble RTX was activated over L-Band through POSView, the control software for the POS MV OceanMaster.

With a fast convergence time, the system was achieving centimetre level accuracy within minutes of activation. The Trimble RTX solution allowed A-2-Sea to complete calibrations and verifications as well as provide an accurate real-time solution during survey operations.

Part of their ongoing survey scope is to report uncharted features on the seabed within a strict 24-hour time frame. The POS MV with Trimble RTX corrections allowed them to do this with confidence.

Conclusion

A-2-Sea successfully completed the mobilisation of their Applanix POS MV OceanMaster on the Noortruck, taking careful consideration of sensor location, undertaking a precise and thorough dimensional control survey, sensor calibrations and equipment verifications, thus ensuring the acquisition of high-quality hydrographic data.

The successful cooperation between Applanix, Trimble and A-2-Sea allowed the testing of the Trimble RTX correction service, which will provide valuable data as the solution starts to become more available to the marine market.

For more information on the Applanix POS MV hardware and POSPac processing software, please visit www.applanix.com or contact marinesupport@aplanix.com

For more information about the Trimble RTX correction service, please visit https://positioningservices.trimble.com/industries/marine/

For more information on A-2-Sea and its services, please contact info@a2sea.co.uk or visit www.a2sea.co.uk.